http://www.tracopower.com page 1 of 4 dc/dc converters tes 1 series, 1 watt features small smd package with standard footprint i/o isolation 1500 vdc single and dual output models input voltage 5, 12 and 24 vdc high effciency up to 80% operating temperature range C40c to +85c high accuracy of pin co-planarity qualifed for leadfree refow solder process according ipc/jedec j-std-020c available in tape and reel package 3-year product warranty with their small footprint these 1watt dc/dc converters are an ideal and economi - cal solution for many applications where an isolated voltage is required. typical ap - plications are ground loop elimination, noise reduction, voltage isolation in digital interfaces and voltage conversion in distributed power systems. with a new pack - age design these converters are qualifed for the higher temperatures requested by lead-free refow solder processes. for automated smd production lines the devices can be supplied in standard tape and reel package. order code input voltage output voltage output current max. effciency typ. tes 1-0510 3.3 vdc 300 ma 73 % tes 1-0511 5 vdc 200 ma 78 % tes 1-0519 9 vdc 110 m a 78 % tes 1-0512 5 vdc 10% 12 v d c 85 ma 78 % tes 1-0513 (nominal 5 vdc) 15 vd c 65 ma 79 % tes 1-0521 5 vdc 100 ma 74 % tes 1-0522 12 v d c 40 ma 78 % tes 1-0523 15 vd c 35 ma 78 % tes 1-1211 5 vdc 200 ma 76 % tes 1-1219 9 vdc 110 m a 78 % tes 1-1212 12 v d c 85 ma 79 % tes 1-1213 12 vdc 10% 15 vd c 65 ma 80 % tes 1-1221 (nominal 12 vdc) 5 vdc 100 ma 74 % tes 1-1222 12 v d c 40 ma 78 % tes 1-1223 15 vd c 35 ma 79 % tes 1-2411 5 vdc 200 ma 78 % tes 1-2419 9 vdc 110 m a 77 % tes 1-2412 12 v d c 85 ma 77 % tes 1-2413 24 vdc 10% 15 vd c 65 ma 79 % tes 1-2421 (nominal 24 vdc) 5 vdc 100 ma 73 % tes 1-2422 12 v d c 40 ma 78 % tes 1-2423 15 vd c 35 ma 78 % models
http://www.tracopower.com input specifications input current no load / full load 5 vin models: 30 ma / 260 ma typ. 12 vin models: 15 ma / 110 ma typ. 24 vin models: 8 ma / 55 ma typ. surge voltage (1 sec. max.) 5 vin models: 9 v max. 12 vin models: 18 v max. 24 vin models: 30 v max. reverse voltage protection 0.3 a max. input filter internal capacitors output specifications voltage set accuracy C 5 vdc models: 2 % at 60 % load C other models: 2 % at 100 % load voltage balance (dual output models, balanced load) 1 % max. regulation C input variation 1.2 % / 1 % change vin C load variation see graphs below ripple and noise (20 mhz bandwidth) 120 mvpp max. temperature coefficient 0.02 %/k short circuit protection limited 0.5 sec. max. capacitive load 33 f max. general specifications temperature ranges C operating C40c to +85c C storage C55c to +125c C case C105c max. derating (convection cooling) 4 %/k above +75c humidity (non condensing) 95 % rel. h max. reliability, calculated mtbf (mil-hdbk-217f, at +25c, ground benign) >2000000 h isolation voltage (60sec.) C input/output 1500 vdc isolation capacitance C input/output 40 pf typ. isolation resistance C input/output >1000 mohm switching frequency 100 khz typ. (frequency modulation) frequency change over line and load 30 % environmental compliance C reach www.tracopower.com/products/tes1-reach.pdf C rohs rohs directive 2002/95/ec dc/dc converters tes 1 series 1 watt all specifcations valid at nominal input voltage, full load and +25c after warm-up time unless otherwise stated. page 2 of 4 output voltage variation dependent on load (at nominal input voltage) 100% 50% 0 0% -10% +10% deviation of v out nom. l oad max. min. ty p. 5 vdc models: 100% 50% 0 0% -10% +10% deviation of v out nom. l oad max. min. ty p. other models:
http://www.tracopower.com page 3 of 4 all specifcations valid at nominal input voltage, full load and +25c after warm-up time unless otherwise stated. dc/dc converters tes 1 series 1 watt physical specifications casing material epoxy molding compound (94v-0 rated) weight single output models: 1.7 g (0.04 oz) dual output models: 2.0 g (0.05 oz) lead-free reflow solder process as per j-std-020d.01 (to find at: www.jedec.org - free registration equired) moisture sensivity level (msl) level 2 as per j-std-033b.01 (to find at: www.jedec.org - free registration required) washing process www.tracopower.com/products/smd- wash.pdf packaging www.tracopower.com / products / t es1 -pack.pdf outline and solder pad dimensions tes 1 single output models pin single 1 Cvin (gnd) 3 +vin (vcc) 7 Cvout 8 +vout 14 *nc pin-out 0.1 0-4 s 0.6 7.0 0.3 8.0 5.5 11.0 0.2 13 7 14 8 (0.28) (0.01) (0.31) (0.216) (0.43 0.008) 3.04 2.54 5.08 13.7 (0.12) (0.10) (0.20) (0.54) t op view 11.6 (0.46) 2.54 5.08 (0.10) (0.10) 1.0 min. 1.6 (0.07) (0.02) (0.04) 5.5 (0.216) 1.5 (0.06) solder pad dimension * pin to be isolated from circuitry dimensions in [mm], () = inch pin pitch tolerances: 0.10 (0.004) other tolerances: 0.25 (0.01) application note: www.tracopower.com/products/tes1-application.pdf
dc/dc converters tes 1 series 1 watt r e v. 07/12 specifcations can be changed any time without notice. pin dual 1 Cvin (gnd) 3 +vin (vcc) 7 common 9 Cvout 12 +vout 18 *nc pin-out tes 1 dual output models 0.6 7.0 0.3 13 7 18 12 (0.28) (0.01) 9 3.04 2.54 5.08 16.3 (0.12) (0.10) (0.20) (0.64) 2.54 (0.10) t op view 0.1 0-4 s 8.0 5.5 11.0 0.2 (0.31) (0.216) (0.43 0.008) 5.5 (0.216) 1.5 (0.06) 11.6 (0.46) 1.0 min. 1.6 (0.07) (0.04) 2.54 5.08 (0.10) (0.10) 2.54 (0.10) dimensions in [mm], () = inch pin pitch tolerances: 0.10 (0.004) other tolerances: 0.25 (0.01) page 4 of 4 * pin to be isolated from circuitry outline and solder pad dimensions jenatschstrasse 1 ch-8002 zurich switzerland t el. +41 43 311 45 11 fax +41 43 311 45 45 info@traco.ch www .tracopower .com
|
